Accessories
Accessories

Show
2.1mm DC Barrel Jack to Alligator Clips 2.1mm, dc, jack, barrel, plug, alligator, clips, power, cord, testing
AF-1328
Price: $1.95 In Stock
Item #: AF-1328 -

    With this 2.1mm DC Barrel Jack to Alligator Clips cable you can easily turn a wall adapter into a power supply! A high quality molded 2.1mm DC barrel jack is brought out to red (center positive) & black (ring negative) alligator clips. Works with most wall adapters. Good for 2-3 Amps and up to 24VDC.

    6%27 USB Cable Extension 6%27, ft, foot, feet, USB, Cable, Extension, white, gold
    CBL-USBMTF-WHT
    Price: $4.95 In Stock
    Item #: CBL-USBMTF-WHT -

      Need to plug in a USB device, but it's just out of reach? Have a short USB cable with a proprietary connector? The 6' USB Extension cable is what you need! This cable has a standard USB A male connector on one end, and a standard USB A female connector on the other, allowing you to extend the reach of virtually any USB cable in your arsenal.

      6v 3a UBEC 2-5S Lipoly (6-32v) 6v, 3a, UBEC, 2-5S, Lipoly, 6-32v, voltage, regulator
      HK-UBEC6V3A
      Price: $6.95 In Stock
      Item #: HK-UBEC6V3A -

        A BEC (battery elimination circuit) is a great tool for getting a lower voltage from a higher voltage system. For example, say you needed 6v to drive a RobotGeek servo on your 11.1v PhantomX Hexapod , but you didn't want to add a secondary battery just for the 6v servo. Simply plug this BEC into your Hexapod's battery and you'll get a stable 6v 3A power supply. The 6v 3a UBEC 2-5S Lipoly (6-32v) is a small and lightweight UBEC, featuring a High efficiency switch mode design that provides...

        Alligator Clip with Pigtail (4 Pack) Alligator Clip with Pigtail, pin header, breadboard, prototyping
        SF-CAB-13191
        Price: $2.95 In Stock
        Item #: SF-CAB-13191 -

          This is a 4 pack of wires that are pre-terminated with an alligator clip on one end and a hookup pigtail on the other. Alligator clips are a staple part for any workbench and with these cables you will be able to easily incorporate those clips into a breadboard, development platform, or anything else that you would normally be able to attach a hookup wire to. Each Alligator Clip with Pigtail cable has a wire length of 30cm (that’s a little less than 1ft) and a male pin that easily inserts into...

          Alligator Test Leads - Multicolored (10 Pack) Alligator Test Leads, Multicolored, alligator clips, prototyping, crocodile clips
          SF-PRT-12978
          Price: $2.95 In Stock
          Item #: SF-PRT-12978 -

            Alligator clips (or Crocodile clips, if you prefer) are likely to be the most useful thing on your workbench besides the workbench itself. Whether you’re just trying to make a few quick connections to test your circuit or having trouble making your multimeter leads stay where you need them, these spring-loaded clips are a workshop must-have. Each lead in this pack of tern is 50cm long with a rubber shrouded alligator clip on each end. There are five different colors, you get two each of: red,...

            Cold 2-Wire Splice (UY) - 10 pack cold, wire, splice, uy, crimp
            AF-1496
            Price: $2.95 In Stock
            Item #: AF-1496 -

              Get connected quickly with a Cold 2-Wire Splice (UY). These little wonders bite into any 22-26 AWG solid core wire with a quick squeeze from some parallel-jaw or slip joint pliers, making a solid butt splice connection. Though not waterproof, the splices contain silicone jelly to keep the cold splice from oxidizing.

              Cold Splice Wire Tap (UB) - 10 pack cold, wire, splice, ub, crimp
              AF-1494
              Price: $2.95 In Stock
              Item #: AF-1494 -

                Get connected quickly with a Cold Splice Wire Tap (UB). These little wonders bite into any 22-26 AWG solid core wires with a quick squeeze from some parallel-jaw or slip joint pliers, making a solid 3-way splice connection. Though not waterproof, the splices contain silicone jelly to keep the cold splice from oxidizing.

                Screwdriver Magnetizer / Demagnetizer Screwdriver, Magnetizer, Demagnetizer
                SS-114990066
                Price: $5.90 In Stock
                Item #: SS-114990066 -

                  The Screwdriver Magnetizer / Demagnetizer is aptly named. Quickly and easily magnetize small tools so they attract screws or nuts for easily starting and removing. Insert a screwdriver or nutdriver into the hole , pull it out and it's magnetized!

                  USB Charger Doctor - In-line Voltage and Current Meter usb, charger, doctor, voltage, current, meter
                  AF-1852
                  Price: $7.50 In Stock
                  Item #: AF-1852 -

                    The USB Charger Doctor is a handy tool that measures the working voltage and current output for any USB port and project. Plug the Doctor between a USB port and your USB device, and it will check the current draw with a 0.05 ohm resistor in line with the power pin. Data lines pass through as normal. You can use this device from 3.5-7VDC input voltage (although most USB devices tend to hover around 4.75 to 5.25) and up to 3A of current. It flips between voltage and current readouts roughly...

                    Sparkfun Cerberus USB Cable Sparkfun Cerberus USB Cable, Sparkfun, Cerberus, USB, Cable, Robot, Data, mini, micro
                    SF-CAB-12016
                    Price: $5.95 In Stock
                    Item #: SF-CAB-12016 -

                      You are in the middle of working on your latest robot, when you need to program a new board you just got in. You dig through your bin of USB cables only to find that you have hundreds that have the wrong end, and exactly zero that have the end you're looking for. As luck would have it, you remember that you ordered the Sparkfun Cerberus USB Cable! With this cable, you will always have the right connection. The Cerberus USB Cable has the standard A-type connector, which you can plug into your...

                      Lithium Ion Battery 7.4v 2200mAh (2S2P) with PCM Lithium, Ion, li-ion, lion, Battery, 7.4V, 2200mAh, 2S2P, PCM, Charger, Samsung, cells
                      BAT-LION7V2200
                      Price: $19.95 In Stock
                      Item #: BAT-LION7V2200 -

                        Power up your rover, or take your robot arm off the grid with the 7.4V 2200mAh Lithium Ion Battery! This battery has excellent capacity for robotics projects utilizing several RobotGeek Servos. To make it easy to connect/disconnect the battery from your project, each of these batteries has a Female T-Connector (Deans Ultra Plug compatble), and for easy charging, a barrel Jack for use with the Charger with over-voltage protection (included). If discharged too low, Lithium Ion batteries can...

                        Robot Geek Small Workbench Robot Geek Small Workbench
                        ASM-WRKBS
                        Price: $7.95 In Stock
                        Item #: ASM-WRKBS -

                          Robot Geek Workbenches are versatile platforms that allow for building modular projects quickly. All Robot Geek products and kits conform to the standard 1 X 1 CM hole pattern grid allowing builders to custom build their projects any way they desire. An infinite number of configurations are possible! The Small Robot Geek Workbench comes with: Small Workbench Plate (16 X 15 CM) 4 X Large Rubber Bumpers

                          RobotGeek Sensor Cable Pack robotgeek, robotgeek sensor pack, robotgeek sensor cable pack, robotgeek cable pack, servo wire, 2 pin jumpers, sensor squid, pin couplers, jr female, y cable, variety pack
                          RG-SPACK
                          Price: $24.95 In Stock
                          Item #: RG-SPACK -

                            The Robot Geek Sensor Cable Pack will hook you up with all your sensor and servo wiring needs and beyond. This variety cable pack includes: 3x 3 Pin Female to Female Y Cable 1x 32 Foot Standard Servo Wire 20x 3 Pin Sensor Cable 10x 2 Pin Dual-Female Jumper Wires (300mm) 10x Sensor Squids 25x 2-Pin Couplers 25x 3-Pin Couplers ...

                            Lithium Ion Battery 7.4V 4400mAh (2S2P) with PCM and Charger Lithium, Ion, li-ion, lion, Battery, 7.4V, 4400mAh, 2S2P, PCM, Charger, Samsung, cells
                            KIT-LIONBAT
                            Price: $39.95 In Stock
                            Item #: KIT-LIONBAT -

                              Power up your rover, or take your robot arm off the grid with the 7.4V 4400mAh Lithium Ion Battery! This battery has excellent capacity for robotics projects utilizing several RobotGeek Servos. To make it easy to connect/disconnect the battery from your project, each of these batteries has a Female T-Connector (Deans Ultra Plug compatble), and for easy charging, a barrel Jack for use with the Charger with over-voltage protection (included). If discharged too low, Lithium Ion batteries can...

                              Robot Geek Large Workbench Robot Geek Large Workbench
                              ASM-WRKBL
                              Price: $8.95 In Stock
                              Item #: ASM-WRKBL -

                                Robot Geek Workbenches are versatile platforms that allow for building modular projects quickly. All Robot Geek products and kits conform to the standard 1 X 1 CM hole pattern grid allowing builders to custom build their projects any way they desire. An infinite number of configurations are possible! The Large Robot Geek Workbench comes with: Large Workbench Plate (21 X 22 CM) 8 X Large Rubber Bumpers

                                RobotGeek 150mm 3-pin Sensor Cable 10 pack
                                CBL-JRFEM150
                                Price: $4.95 In Stock
                                Item #: CBL-JRFEM150 -

                                  RobotGeek Sensor Cables are for use with all RobotGeek sensors, shields, servos, and output devices. These cables are .1"(2.54mm) pitch and are 150mm in length with color coded wires. Add some 3-Pin Couplers to connect cables together for extension cables. These cables are also compatible with Phidgets Sensors and Electronic Brick Sensors, though they do not have the plastic buckle like traditional Phidgets/Electronic Brick Cables. ...

                                  Lithium-ion Battery Charger Lithium-ion Battery Charger
                                  CHG-LION
                                  Price: $12.95 In Stock
                                  Item #: CHG-LION -

                                    Standard Lithium-Ion Battery Charger intended for use with the Lithium Ion Battery 7.4v 2200mAh (2S2P) with PCM.

                                    300mm 3-pin Female Sensor Cable 10 pack
                                    CBL-JRFEM
                                    Price: $4.95 In Stock
                                    Item #: CBL-JRFEM -

                                      RobotGeek Sensor Cables are for use with all RobotGeek sensors, shields, servos, and output devices. These cables are .1"(2.54mm) pitch and are 300mm in length with color coded wires. Add some 3-Pin Couplers to connect cables together for extension cables. These cables are also compatible with Phidgets Sensors and Electronic Brick Sensors, though they do not have the plastic buckle like traditional Phidgets/Electronic Brick Cables. ...

                                      RobotGeek Double Wide Workbench RobotGeek, robot, geek, Double, 2x, Wide, Workbench, large, centimeter, grid, mounting, plate
                                      ASM-WRKBD
                                      Price: $14.95 In Stock
                                      Item #: ASM-WRKBD -

                                        Is your large workbench feeling cramped with all the RobotGeek Sensors you've added to it? Never fear, the RobotGeek Double Wide Workbench covers it! Just as tall and twice as wide as a RobotGeek Large Workbench at 44x21 Centimeters. Robot Geek Workbenches are versatile platforms that allow for building modular projects quickly. All Robot Geek products and kits conform to the standard 1 X 1 CM hole pattern grid allowing builders to custom build their projects any way they desire. An infinite...

                                        Servo Cable
                                        CBL-32SEN
                                        Price: $12.95 In Stock
                                        Item #: CBL-32SEN -

                                          Our 32 Feet Standard Servo Wire is great for repairing and extending servo and sensor cables. The Futaba Black-Red-White (Ground-Voltage-Signal) color scheme will help you keep your signals straight. This cable has 24awg stranded wire and no connectors on either end.

                                          LiPo/Li-ion Battery Wiring Harness battery, wiring, harness, power, dean plug, barrel plug, battery link, lipo battery harness, lipo harness
                                          CBL-HARNESS
                                          Price: $8.95 In Stock
                                          Item #: CBL-HARNESS -

                                            Easily link your project to a LiPo/Li-ion battery with the Battery Wiring Harness! This harness is the same one we use in our Hexapod and Quadruped kits. Just attach the male Dean connector to any of our LiPo/Li-ion Batteries and the barrel jack plug into your project, and you're ready to go! The harness even has a built in switch to quickly shut down power to your project. The switch is easily mountable - just cut a 6mm hole into your project and use the included nut and washer to securley...

                                            RobotGeek Mega Workbench RobotGeek, Mega, large, Workbench, centimeter, grid, project
                                            ASM-WRKBM
                                            Price: $24.95 In Stock
                                            Item #: ASM-WRKBM -

                                              Have a really big project? The Robotgeek Mega Workbench is the solution! At a total whopping 44x42 centimeters, you'll have all the room you need for a project of epic proportions! It really can't be stated enough just how huge this thing really is. RobotGeek Workbenches are versatile platforms that allow for building modular projects quickly. All RobotGeek products and kits conform to the standard 1 X 1 CM hole pattern grid allowing builders to customize their projects any way they desire. An...

                                              RobotGeek Workbench Joiner Brackets RobotGeek, robot, geek, Workbench, Joiner, Plates, hardware, brackets
                                              ASM-BENCH-BRACKET
                                              Price: $4.95 In Stock
                                              Item #: ASM-BENCH-BRACKET -

                                                Have a couple RobotGeek Workbenches and a big project? The RobotGeek Workbench Joiner Brackets will do the trick! These are the same brackets included in the RobotGeek Mega Workbench that make it so mega. You can easily bolt together some workbenches for a larger footprint than would be capable with any single workbench. Kit Contents: 2 X Delrin Workbench Joiner Brackets 10 X M3x6 Bolts

                                                6 Inch Digital Calipers in box
                                                SF-TOL-10997
                                                Price: $14.95 In Stock
                                                Item #: SF-TOL-10997 -

                                                  6th Century BC: One of the earliest known calipers is lost on an Italian coast, to be found centuries later. 1851: Joseph R. Brown invents the modern vernier caliper. Today: You can own the next evolution in calipers, the Digital Caliper Whether you're measuring a component to get just the right fit in your project box, or you're trying to replicate a complex widget with your 3D printer, you'll need a trusty set of calipers by your side. These calipers even have a data out! This is great for...

                                                  Arduino Project Box Arduino, Project, Box, Duemilanove, Diecimila, Arduino Board, Arduino Kit, Arduino Diecimila USB IO Board, Arduino IO Board, Arduino Diecimila, Arduino Diecimila Board
                                                  MG-A000009
                                                  Price: $11.95 In Stock
                                                  Item #: MG-A000009 -

                                                    What we have here is a (flame retardant) Arduino Project Box that allows you to safely enclose your Arduino + Shield projects and then set them on fire. Just kidding, please don't. But seriously! Rob your Arduino projects of their nudist free spirit attitudes and put some clothes on them, dang hippies. This enclosure can fit pretty much all Arduino and Arduino Mega models, as well as a majority of shields. It has specifically designed removable ports for use with the Arduino Ethernet shield....

                                                    Power Supply 6VDC 2.0A - US Power Supply 6VDC 2.0A, Power Supply, 6VDC, 2 amp
                                                    POW-6v2a
                                                    Price: $9.95 On Hold
                                                    Item #: POW-6v2a -

                                                      Power Supply for general project use.North American Style Plug6VDC, 2 Amp, Center Positive Polarity, 5.5x2.1MM

                                                      RobotGeek GeekBot Top Deck RobotGeek, robot, geek, GeekBot, bot, rover, Top, Deck, workbench
                                                      PRT-GEEKDECK
                                                      Price: $9.95 In Stock
                                                      Item #: PRT-GEEKDECK -

                                                        Spruce up your rover with the RobotGeek GeekBot V2 Top Deck! This 265mm diameter round deck has the standard 1 X 1 CM Robot Geek grid pattern making it easy to mount your sensors, batteries, ~duino boards, and accessories anywhere you need.

                                                        Sensor Y Cable - 100mm sensor Y cable, sensor splitter cable, servo y cable, servo splitter cable
                                                        CBL-3PF2Y
                                                        Price: $1.95 In Stock
                                                        Item #: CBL-3PF2Y -

                                                          The Sensor Y Cable is a great tool for splitting a single signal to multiple output boards. These cables are 100mm long and use a standard .1"/2.54mm pitch, making them compatible with RobotGeek I/O boards, Hobby servos, and breadboards. With this cable you can easily connect from a single output port on the RobotGeek Sensor Shield to a RobotGeek Relay, a RobotGeek LED Driver or a RobotGeek Buzzer. Combine this cable with 2 3-Pin Couplers to easily connect from 1 port to 2 Hobby Servos. You...

                                                          7v5A Power Supply
                                                          POW-7v5A
                                                          Price: $11.95 In Stock
                                                          Item #: POW-7v5A -

                                                            7VDC, 5 Amp Power Supply for general project use. Center Positive Polarity, 5.5x2.1MM barrel jack.

                                                            Plastic Project Box and Mouting Hardware arduino project box, arduino box, arduino weather proof box, arduino water proof box, water proof arduino box, weather proof arduino box
                                                            ASM-PRBOX
                                                            Price: $8.95 In Stock
                                                            Item #: ASM-PRBOX -

                                                              The Project Box for Arduino is a great starter enclosure for your Arduino. This waterproof box can be used for logging purposes, or you can drill/paint/cut apart the box to suit whatever your needs are! A special mounting plate allows you to mount your Arduino and a shield in a variety of orientations with ease.

                                                              Squid Cable
                                                              CBL-SQUID
                                                              Price: $4.95 In Stock
                                                              Item #: CBL-SQUID -

                                                                Sometimes you need to hook a servo or a sensor directly to your Arduino, or minimize the mess of jumper wires on your breadboard. These Squid Sensor Cables - 10 pack will help you do just that! On one end, you have a standard 3-pin connector (.1"/2.54mm pitch), and on the other end you have 3 single female jumper wires. You can easily position each cable exactly where you need it. and are 200mm in length. Add some 3-Pin Couplers to attach these cables directly to a servo or your arduino. These...

                                                                3-Pin Couplers
                                                                S-200-3P-Coupler-25pack
                                                                Price: $2.95 In Stock
                                                                Item #: S-200-3P-Coupler-25pack -

                                                                  You can use these 3 pin couplers to connect 3 pin jumper wires together and create your own extension wires. This is perfect for extending analog sensors or servos! You can also use them to make modular connectors on your breadboard/protoboard so that connecting to other components is even easier. The pins on these couplers are spaced at .1"/2.54mm, so they're compatible with Electronic Brick/Phidgets sensor cables, hobby servo cables, and most breadboards/protoboard. They are NOT compatible...

                                                                  12V 2A DC Power Supply
                                                                  POW-12v2a
                                                                  Price: $10.95 In Stock
                                                                  Item #: POW-12v2a -

                                                                    Power Supply for general project use. North American Style Plug 12VDC, 2 Amp, Center Positive Polarity, 5.5x2.1MM PS - You might want one of these too.

                                                                    Treasure Project Box project box, arduino project box, rfid project box, rfiduino project box, treasure chest box, treasure box, treasure project box
                                                                    RW-WBOX
                                                                    Price: $9.95 In Stock
                                                                    Item #: RW-WBOX -

                                                                      Sometimes a regular project box just isn’t enough. You need some flash, some mystery, some style. We understand, we felt the same way. We had these wooden treasure boxes special made for a few of our own projects and now you can DIY in style too. Why make your project in a plain box when you can make it look like a mysterious magic box bought in a dangerous back alley in some remote corner of the world? Time to step up your DIY game. We recommend using our Panel Mount Dual Power Cable with the...

                                                                      4 Pin Sensor Cable 300mm 4 pin sensor cable, 4pin sensor cable, lcd sensor cable, lcd cable, 4pin cable, 4 pin cable, sensor cable
                                                                      CBL-4PINSEN
                                                                      Price: $1.95 In Stock
                                                                      Item #: CBL-4PINSEN -

                                                                        This standard 4 Pin Sensor Cable is 30cm long and has a .1"/2.54mm pitch, making it compatible with 4-pin sensors and shields. You can also add Pin Couplers and attach the cable to breadboards.

                                                                        Power Supply 12V - 5A (2.1mm Jack) Power Supply 12VDC 5.0A - US
                                                                        POW-12v5a
                                                                        Price: $19.95 In Stock
                                                                        Item #: POW-12v5a -

                                                                          Power Supply for general project use. North American Style Plug 12VDC, 5 Amp, Center Positive Polarity, 5.5x2.1MM PS - You might want one of these too.

                                                                          RobotGeek 4 Pin Sensor Squid 300m 4 pin, sensor, cable, squid, data, 300m, jumper, breakout
                                                                          CBL-SQUID4P
                                                                          Price: $4.95 In Stock
                                                                          Item #: CBL-SQUID4P -

                                                                            Sometimes you need to hook a serial/I2C device directly to your Arduino, or minimize the mess of jumper wires on your breadboard. These 4 Pin Sensor Squid 300m cables will help you do just that! On one end, you have a standard 4-pin connector (.1"/2.54mm pitch), and on the other end you have 4 single female jumper wires. You can easily position each cable exactly where you need it. Each cable is 300m in length. Comes in pack of 10 squid cables. Pair these cables with 2-pin couplers to adapt...

                                                                            Variable Power Supply 15-24V 4.5A (2.1mm Jack) Variable Power Supply 15-24VDC 4.5A - US
                                                                            POW-Variable
                                                                            Price: $24.95 In Stock
                                                                            Item #: POW-Variable -

                                                                              Variable Power Supply for general project use. North American Style Plug 15-24VDC 4.5A - US Center Positive Polarity, 5.5x2.1MM PS - You might want one of these too.

                                                                              12v10a Power Supply 12v10a Power Supply
                                                                              POW-12v10A
                                                                              Price: $19.95 In Stock
                                                                              Item #: POW-12v10A -

                                                                                12VDC, 10 Amp Power Supply for general project use.Center Positive Polarity, 5.5x2.1MM barrel jack.

                                                                                140mm Slewing Bearing slewing bearing, robot slewing bearing, robot arm base bearing
                                                                                RW-140BEARING
                                                                                Price: $19.95 In Stock
                                                                                Item #: RW-140BEARING -

                                                                                  The 140mm Slewing Bearing is the same bearing found in our Robotic Arms. Each bearing is made of a soft aluminum alloy and sports a single row of spherical bearings. These bearings give the bearing a silky smooth movement, perfect for assisting your robotic arm base, or just about any other moving joint. The slewing bearing goes great with the Standoff Variety Pack and the Nut and Bolt Variety Pack, giving you all the hardware you need to attach the bearing to a variety of projects. ...

                                                                                  150mm Jumper Wires F/F (Set of 10)
                                                                                  AC-200-PRT08430
                                                                                  Price: $3.95 In Stock
                                                                                  Item #: AC-200-PRT08430 -

                                                                                    These Jumper Wires F/F (Set of 10) are great for connecting male headers from one board to another. Combine them with Male Jumpers to make even longer cables! These jumpers will fit neatly into a .1" header, so they're great for bread boards. Each pack of 10 comes with cables in 5 colors. Each cable is 150mm long

                                                                                    2-Pin Couplers
                                                                                    S-200-2P-Coupler-25pack
                                                                                    Price: $2.95 In Stock
                                                                                    Item #: S-200-2P-Coupler-25pack -

                                                                                      You can use these 2 pin couplers to connect 2/4 pin jumper wires together and create your own extension wires. You can also use them to make modular connectors on your breadboard/protoboard so that connecting to other components is even easier. The pins on these couplers are spaced at .1"/2.54mm, so they're compatible with Electronic Brick/Phidgets sensor cables and most breadboards/protoboard. They are NOT compatible with Grove cables. ...

                                                                                      4x AA Battery to 2.1/5.5mm DC Barrel Jack AA, Battery, 2.1, 5.5, DC, Barrel, Jack, pack, holder, 4x
                                                                                      BAT-AAPACK
                                                                                      Price: $2.95 In Stock
                                                                                      Item #: BAT-AAPACK -

                                                                                        This 4x AA Battery to 2.1/5.5mm DC Barrel Jack is perfect for small mobile Arduino Projects. Just add 4 AA batteries and plug the barrel jack into your Arduino Board, and you're ready to rock! Supplies just over 6 volts of power with a fresh set of batteries, which works well with a wide variety of projects. Great for infrared, LED, or any small Arduino project you'd like to take on the go!

                                                                                        Electronic Brick - Fully Buckled 3 Wire Cable - 5 Pack
                                                                                        SEEED-ELB111C5M
                                                                                        Price: $4.99 In Stock
                                                                                        Item #: SEEED-ELB111C5M -

                                                                                          5 pack of fully buckled 3 wire cables for the Electronic Brick family of products.

                                                                                          Jumper Wires - Connected 6" (M/F, 20 pack)
                                                                                          SF-PRT-12794
                                                                                          Price: $1.95 In Stock
                                                                                          Item #: SF-PRT-12794 -

                                                                                            These are 6" long jumper wires terminated as male to female. Use these to jumper from any male or female header on any board. Multiple jumpers can be connected next to one another on a 0.1" header. Comes in one pack of 20 jumpers (colors shown). Each group of jumpers are connected to each other and can either be pulled apart in any quantity (from 1-20, of course) or kept whole based on you needs. These jumper wires can be used for pretty much everything! They work great with breadboards,...

                                                                                            Pin Headers Experimental Pack Pin Headers Experimental Pack
                                                                                            SS-STR131B2P
                                                                                            Price: $7.95 Back Order
                                                                                            Item #: SS-STR131B2P -

                                                                                              This pack included 41 parts of most commonly used Pin-headers. Perfect for your breadboard/protoboard project. Parts List Female 1*40 2.54mm pin headers X1 Male 1*40 2.54mm pin headers X2 Male 1*40 2.54mm pin headers, stackable Male 1*40 2.54mm pin headers, bend on board X1 Male 1*40 2.54mm pin headers, bend above board X1 Female 1*8 2.54mm pin headers, bend on board X3 Female 1*6 2.54mm pin headers, bend on board X3 Female 1*8 2.54mm pin headers, stackable X3 Female 1*6 2.54mm pin headers,...

                                                                                              Turbo Fuse Super Glue 10ml
                                                                                              PL-15180
                                                                                              Price: $9.95 In Stock
                                                                                              Item #: PL-15180 -

                                                                                                Turbo Fuse Super Glue is a standard super glue in a thicker viscosity. It is metal and plastic safe and recommended for use with high vibration robots when you really need a lot of holding strength to keep your nuts and bolts in place.This is a 10ml bottle intended for larger projects. You can find the smaller 2ml vial here.

                                                                                                Turbo Fuse Super Glue 2ml
                                                                                                PL-04180
                                                                                                Price: $3.95 Back Order
                                                                                                Item #: PL-04180 -

                                                                                                  Turbo Fuse Super Glue is a standard super glue in a thicker viscosity. It is metal and plastic safe and recommended for use with high vibration robots when you really need a lot of holding strength to keep your nuts and bolts in place.This is a 2ml vial intended for smaller projects. You can find the 10ml bottle here.